JCS Upper Stock Angle Block Kit
fits upper position JCS stocks
The JCS Stock Angle Kit allows you to modify your existing JCS folding stock at 0, 6, 8, and 10 degree angles. Improves mask clearance and makes sighting easier. Even if you don't use the sights, this kit brings the marker up higher allowing better sighting. Includes stainless steel mounting bolts.

59150

$6.00
 

JCS Lower to Upper Conversion Kit
Converts Grip-Mount stocks to Upper
This kit allows you to modify your existing grip-mount JCS stock to an upper position stock. It also includes at 0, 6, 8, and 10 degree angles. Improves mask clearance and makes sighting easier. Even if you don't use the sights, this kit brings the marker up higher allowing better sighting. Includes stainless steel mounting bolts. Fits all JCS gun mounts and RVA's in upper position. RVA's 66148, 66149, 66152, and all similar non-RVA gun mounts too!

59151

$11.00
 

JCS Rubber Shoulder PAD
for any JCS item #661xx
Comfortable rubber design. Unique look & feel. Works on your existing JCS folding stock.

66261

$3.75
 

Knob, Bolt, and E-Clip replacement KIT
for any JCS item #661xx
Genuine ORIGINAL by the inventor, Steve Wygant. This kit repairs any JCS Folding stock with slide assembly. Or, if you have a stock that is a several years old, you can buy this as an upgrade!

66133

$6.95
 

JCS Stock Grip Mount Kit
for Grip Mounting to Any Marker
Already own a JCS Folding Stock? This grip-mount part is the same as in our product 66190 Combat Stock. It will mount to Tippmann's, Spyder's, or Piranha's, and just about any other marker out there! A Stock is NOT included, just the bracket. Requires dis-assembly of the locking hinge. Use 5/32 Allen Wrench and 3/8 socket. Includes one bracket and mounting hardware.

66141

$7.60

JCS Stock Adapter Kit
for Spyder's and Piranha's
Already own a JCS Folding Stock? This adapter will mount JCS Folding Stocks to a Spyder or Piranha paintball markers. Mounts stock as shown in picture to the grip above your hand. The MP stock shown is discontinued. A Stock is NOT included, just the bracket and hardware to mount a stock to the gun. Includes one bracket and mounting hardware.

66151

$7.50

on stock

Stock Drop Block
for JCS Stocks and RVA's
This curved block and screws allows you to mount JCS stocks to the bottom of RVA's or drop your existing about 1 inch. Includes black saddle block and two 10-32 x 3/4 long SHCS. 5/32 Allen wrench required. Works with ANY UPPER-MOUNTED JCS folding stock: 66177, 66192, 66195. See pictures to left for use.

71364

$6.50

Combat Folding Stock KIT
for JCS RVA's and gun mounts only
 Already own a JCS RVA? This KIT mounts JCS gun mounts or RVA's which are attached to your marker in the upper position (will not work with grip mounted stocks). This product will not work alone. You get the stock, slide, hinge, and mounting hardware. Just use a 5/32 Allan wrench for installation!

66171

$48.00

VooDoo Folding Stock KIT
for JCS RVA's and gun mounts only
 Already own a JCS RVA? This KIT mounts JCS gun mounts or RVA's which are attached to your marker in the upper position (will not work with grip mounted stocks). This product will not work alone. You get the stock, slide, hinge, and mounting hardware. Just use a 5/32 Allan wrench for installation!

66173

$48.00

JCS Offset Rail CLAMP Kit
fits 3/8 Dovetails
Used in JCS 732xx and JCS 754xx series rail products.
This handy little bar clamp secures to 3/8 dovetails of any paintball marker. Learn more about dovetails here. The holes are tapped for 3mm x 0.5mm pitch machine screws. Machined from aircraft aluminum. Includes bar, clamp, and stainless hardware. Qty One bar assembly per package.

73234
Black

7.60 ea

JCS Offset Rail CLAMP Only
for 7/8 Dovetails
Used in 7/8 " JCS Rail Kit Accessory Mounting Rails
This offset clamp mounts to 7/8 MIL-STD rails. Gap on rail (that this clamp mounts to) must be 0.204 inch minimum width.

73228

$8.60

JCS Round On-Center CLAMP Only
for 3/8 Dovetails
Used in JCS 732xx and 754xx series Accessory Mounting Rails
This handy little bar clamps securely to 3/8 dovetails of any paintball marker. Learn more about dovetails here. The holes are tapped for 3mm x 0.5mm pitch machine screws. Machined from aircraft aluminum. Includes Round Rail Mount, clamp, and stainless hardware. Qty One clamp assembly per package.

73235

6.50 ea

JCS Duel Trigger for A-5 Springs Only
Replacement Springs
 This is a three pack of stainless steel springs used in the JCS Duel Trigger. Genuine JCS Replacement parts!

75707

2.50
 

JCS Double Trigger Guard
for JCS A-5 Duel Trigger
One black composite double trigger guard.

75704
Black

$7.00